Category Index
This instruction sheet describes the connection to the -48VDC or 24VDC Power Card and features a Phoenix terminal block with screw clamp connectors.
This instllation guide provides the necessary information for installing the optional -48VDC Power Supply Card (/DC card) into an Asentria SiteBoss 550, SiteBoss 530, TeleBoss 850, or TeleBoss 830 product.
This document explains the installation of AC Power sensor to be used for monitoring up to 120 VAC.
This document contains instructions for installing the Alarm Button Kit.
This article describes the installation and operation of the optional backup battery module.
This article describes the configuration and use of IP camera alarming using Asentria products.
This guide assists in the installation of a new System Sensor Carbon Monoxide Detector (ESC-CO1), and integration with a SiteBoss or TeleBoss unit.
The DC Current Transducer is used to monitor DC current flow. This document gives installation and configuration instructions.
This article gives instructions for connecting a laptop or a desk top computer directly to the Eth1 or Eth2 ports on a S550 or a T850.
This guide provides information needed to properly connect and configure a ES-32C8V8R high density expansion card and cable for use.
This document describes the installation and configuration instructions for the Resistive Fuel Sensor Adapter
This document provides specifications and installation instructions for an ES-Surge.
This guide provides information needed to properly mount and connect an ESJ-HUB SensorJack Expansion Hub for use with SiteBoss or TeleBoss products.
This document explains how the ES-6INJ EventSensor Power Injector can be used to add power to extend the length of any ES Sensor chain.
This article describes the use and configuration of the EventSensor Reporting feature which allows one SiteBoss to report EventSensor data to a host SiteBoss.
This document describes the correct procedures for field installation of Expansion Cards in Asentria
Asentria Base units have a wide variety of Expansion cards that can be added to our two and six expansion card base units. This makes are units do exactly what a customer needs and reduces cost, since you do not have to buy what you don't need.
This document provides instructions for physical installation and access configurations when using an Asentria-provided Gas Pressure Switch.
This document describes the optional GPS card, its interface with the host unit, and applicable settings.
This document explains how High Density EventSensors add the ability to connect to units using a standard EventSensor connection. These add 32 contact closure points, 8 voltage sensors and 8 form C relay points to a SiteBoss site.
This guide provides information needed to properly connect and configure a high density expansion card and cable and punch down pinouts.
This document gives instructions for installing a SIM into a ML1V or an ML1P 4G Wireless Modem and getting the basic settings configured to connect to the wireless network.
This document briefly describes the basic integration between Intermapper and Asentria SiteBoss monitoring devices.
This guide describes how to configure No-Data, Scheduled, % full, and other Misc.alarms found in the TeleBoss and Siteboss products.
This guide provides information needed to properly install and configure an outdoor door sensor for use with SiteBoss or TeleBoss products
This document provides the necessary information on installing the PB-R30 Relay Switch.
This document describes the use and configuration of the Slimline Relay which provides a simple means of verifying whether AC voltage is present or a switch (AC or DC power) is on or off.
The Rochester Removable Dial Fuel Gauges are used to remotely monitor the fuel level of a diesel or propane fuel tank.
This feature guide shows the pinout for our RJ45 Serial Ports on the TeleBoss and SiteBoss units. The DCE and DTE adapter wiring pin outs is also covered.
This document describes the Installation instructions for the power and relay harness on the SiteBoss 570
This article describes the use and configuration of the EventSensor Reporting feature which allows one SiteBoss to report EventSensor data to a host SiteBoss.
Step by step instructions for installing the SIM(s) into the internal modem on an S360-0
Step by step instructions for how to install the S360-4 SIM(s).
This document provides guidance to installation technicians or Asentria Sales engineers to evaluate the SiteBoss configuration and equipment needed for an individual stationary site.
Spec and installation instructions for the DC n Smoke and Heat Detector
This guide provides information needed to properly install a smoke sensor for use with SiteBoss or TeleBoss products.s.
This Feature Guide contains the basic setup instructions to enable TACACS+ authentication access to a SiteBoss
The Water Sensor Adapter was needed for early hardware versions. This is installation and configuration instructions if the adapter is needed.
This article describes the Installation and usage instructions for the 5001- 044, 5001- 045, 5001- 046 and 5000- 004 Water Sensors
This article provides instructions for physical installation and access configurations when using a Wiegand access card reader and the Asentria Wiegand Card Reader SiteBoss Interface
